RED RAVEN Firmware

release history

VERSION 7.4.1

150.5 MB

Release Date:

10/19/2020

Release Notes

DSMC2 Release Build v7.4.1 October 19, 2020

NOTE: Download the latest versions of REDCINE-X PRO and the RED ROCKET Installer or the RED ROCKET-X Installer from red.com/downloads.

IMPORTANT:

You cannot downgrade the camera to earlier than v7.0.2 after upgrading to v7.4.0.
You must upgrade your REDMOTE firmware to v9.7.x. Download the firmware upgrade from red.com/downloads.
Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
Refer to https://support.red.com/hc/en-us/articles/225544547 for supported Canon lenses.
Refer to https://support.red.com/hc/en-us/articles/225724728 for supported Nikon lenses.
Refer to https://support.red.com/hc/en-us/articles/225565627 for supported PL lenses.
Preset files created only on v4.0.x or later are compatible with v7.4.0.
User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.
It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADE DSMC2 FIRMWARE TO v7.4.0

1. Connect a RED MINI-MAG to your computer.
2. Download the most recent firmware from www.red.com/downloads.
3. Unzip the firmware zip file.
4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.
5. Eject or unmount the SSD, and then remove the SSD.
6. Ensure the camera is powered down.
7. Insert the SSD with the force_upgrade folder into your camera.
8. Power up the camera.
The upgrade automatically runs at power up. During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

9. After the camera powers down, remove the SSD and wait 10 seconds.
10. Power up the camera.
The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.
11. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.
12. Reformat the SSD before recording to it.

SIGNIFICANT CHANGES SINCE PREVIOUS BUILD v7.3.0

Added 1.8x ANA support for MONSTRO 8K VV
Added Zeiss/Fujinon shading commands support
Fixed intermittent media mounting issue
Fixed missing external metadata in R3D with no lens mount installed
Changed camera position character range to A-Z
Changed Output Tone Map default to Medium Contrast
Improved IPP2 to allow for LUTs with built-in output transforms
Improved color reproduction of daylight light sources

OPERATIONAL NOTES SPECIFIC TO BUILD v7.4.0

Perform sensor calibration after upgrade.
Refer to https://support.red.com/hc/en-us/sections/204939547 for the list of Known Issues.
Secure Format media before using Pre-Record.
The horizon feature requires Gyro calibration be completed prior to use.
Do not 3D sync when GEN ICON is not illuminated or yellow.
Image Magnify is available during preview only.
HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

VERSION 7.3.0

137 MB

Release Date:

12/17/2019

Release Notes

DSMC2 Release Build v7.3.0 December 17, 2019

NOTE: Download the latest versions of REDCINE-X PRO and the RED ROCKET Installer or the RED ROCKET-X Installer from red.com/downloads.

IMPORTANT:

You cannot downgrade the camera to earlier than v7.0.2 after upgrading to v7.3.0.
You must upgrade your REDMOTE firmware to v9.7.x. Download the firmware upgrade from red.com/downloads.
Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
Refer to https://support.red.com/hc/en-us/articles/225544547 for supported Canon lenses.
Refer to https://support.red.com/hc/en-us/articles/225724728 for supported Nikon lenses.
Refer to https://support.red.com/hc/en-us/articles/225565627 for supported PL lenses.
Preset files created only on v4.0.x or later are compatible with v7.3.0.
User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.
It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADE DSMC2 FIRMWARE TO v7.3.0

1. Connect a RED MINI-MAG to your computer.
2. Download the most recent firmware from www.red.com/downloads.
3. Unzip the firmware zip file.
4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.
5. Eject or unmount the SSD, and then remove the SSD.
6. Ensure the camera is powered down.
7. Insert the SSD with the force_upgrade folder into your camera.
8. Power up the camera.
The upgrade automatically runs at power up. During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

9. After the camera powers down, remove the SSD and wait 10 seconds.
10. Power up the camera.
The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.
11. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.
12. Reformat the SSD before recording to it.

SIGNIFICANT CHANGES SINCE PREVIOUS BUILD v7.2.4

Added DSMC2 Dragon-X 6K support
Fixed intermittent HD-SDI output with V-Lock IO Expander
Fixed playback color in low light scenes
Fixed horizontal lines on startup with DSMC2 RED TOUCH 7.0" LCD

OPERATIONAL NOTES SPECIFIC TO BUILD v7.3.0

Perform sensor calibration after upgrade.
Refer to https://support.red.com/hc/en-us/sections/204939547 for the list of Known Issues.
Secure Format media before using Pre-Record.
The horizon feature requires Gyro calibration be completed prior to use.
Do not 3D sync when GEN ICON is not illuminated or yellow.
Image Magnify is available during preview only.
HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

VERSION 7.2.4

137.4 MB

Release Date:

7/22/2019

Release Notes

DSMC2 Release Build v7.2.4 June 22, 2019

NOTE: Download the latest versions of REDCINE-X PRO and the RED ROCKET Installer or the RED ROCKET-X Installer from red.com/downloads.

IMPORTANT:

You cannot downgrade the camera to earlier than v7.0.2 after upgrading to v7.2.4.
You must upgrade your REDMOTE firmware to v9.7.x. Download the firmware upgrade from red.com/downloads.
Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
Refer to https://support.red.com/hc/en-us/articles/225544547 for supported Canon lenses.
Refer to https://support.red.com/hc/en-us/articles/225724728 for supported Nikon lenses.
Refer to https://support.red.com/hc/en-us/articles/225565627 for supported PL lenses.
Preset files created only on v4.0.x or later are compatible with v7.2.4.
User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.
It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMC2FIRMWARE TO BUILD v7.2.4

1. Connect a RED MINI-MAG to your computer.
2. Download the most recent firmware from www.red.com/downloads.
3. Unzip the firmware zip file.
4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.
5. Eject or unmount the SSD, and then remove the SSD.
6. Ensure the camera is powered down.
7. Insert the SSD with the force_upgrade folder into your camera.
8. Power up the camera.
The upgrade automatically runs at power up. During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

9. After the camera powers down, remove the SSD and wait 10 seconds.
10. Power up the camera.
The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.
11. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.
12. Reformat the SSD before recording to it.

SIGNIFICANT CHANGES SINCE PREVIOUS BUILD v7.2.2

Added Core SWX EVO Module support
Fixed DSMC2 EVF color mismatch with IPP2
Fixed banding artifacts with MONSTRO when Sensor Flip/Mirror Scan Direction enabled
Fixed Apple ProRes file metadata for Rec. 2020
Fixed Apple ProRes output transform with Rec. 2020 baked-in settings
Change to only display voltage for all Gold Mount batteries

OPERATIONAL NOTES SPECIFIC TO BUILD v7.2.4

Perform sensor calibration after upgrade.
Refer to https://support.red.com/hc/en-us/sections/204939547 for the list of Known Issues.
Secure Format media before using Pre-Record.
The horizon feature requires Gyro calibration be completed prior to use.
Do not 3D sync when GEN ICON is not illuminated or yellow.
Image Magnify is available during preview only.
HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

VERSION 7.2.2

137.4 MB

Release Date:

4/25/2019

Release Notes

DSMC2 Release Build v7.2.2 April 25, 2019

NOTE: Download the latest versions of REDCINE-X PRO and the RED ROCKET Installer or the RED ROCKET-X Installer from red.com/downloads.

IMPORTANT:

You cannot downgrade the camera to earlier than v7.0.2 after upgrading to v7.2.2.
You must upgrade your REDMOTE firmware to v9.7.x. Download the firmware upgrade from red.com/downloads.
Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
Refer to https://support.red.com/hc/en-us/articles/225544547 for supported Canon lenses.
Refer to https://support.red.com/hc/en-us/articles/225724728 for supported Nikon lenses.
Refer to https://support.red.com/hc/en-us/articles/225565627 for supported PL lenses.
Preset files created only on v4.0.x or later are compatible with v7.2.2.
User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.
It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v7.2.2

1. Connect a RED MINI-MAG to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

6. Ensure the camera is powered down.

7. Insert the SSD with the force_upgrade folder into your camera.

8. Power up the camera.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

9. After the camera powers down, remove the SSD and wait 10 seconds.

10. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

11. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

12. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v7.2.1

Updated DSMC2 Production Module support

OPERATIONALNOTESSPECIFIC TO BUILD v7.2.2

Perform sensor calibration after upgrade.
Refer to https://support.red.com/hc/en-us/sections/204939547 for the list of Known Issues
Secure Format media before using Pre-Record.
The horizon feature requires Gyro calibration be completed prior to use.
Do not 3D sync when GEN ICON is not illuminated or yellow.
Image Magnify is available during preview only.
HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

VERSION 7.1.0.1

143.7 MB

Release Date:

11/27/2018

Release Notes

DSMC2 Release Build v7.1.0.1 November 27, 2018

NOTE: Download the latest versions of REDCINE-X PRO and the RED ROCKET Installer or the RED ROCKET-X Installer from red.com/downloads.

IMPORTANT:

You cannot downgrade a camera to earlier than v7.0.2 after upgrading to v7.1.0.1.
You must upgrade your REDMOTE firmware to v9.7.x. Download the firmware upgrade from red.com/downloads.
Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
Refer to https://support.red.com/hc/en-us/articles/225544547 for supported Canon lenses.
Refer to https://support.red.com/hc/en-us/articles/225724728 for supported Nikon lenses.
Refer to https://support.red.com/hc/en-us/articles/225565627 for supported PL lenses.
Preset files created only on v4.0.x or later are compatible with v7.1.0.1.
It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADE DSMC2 FIRMWARE TO v7.1.0.1

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (RED MINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANT CHANGES SINCE PREVIOUS BUILD v7.0.4

Added DSMC2 BRAIN support
Added Sensor Flip/Mirror Scan Direction for DSMC2 MONSTRO 8K VV
Added User-Defined Voltage Alert
Added focus peaking tool
Added ability to import CDLs, RMDs, and LUTs
Added 5K 4:3 and 5K 4:3 2x ANA support to EPIC-W 8K S35, DSMC2 8K S35 and DSMC2 8K VV
Added option to select a center mark dot (small/medium + color)
Added Hybrid Log-Gamma display preset
Added Avid DNxHD/HR HQ codec recording standalone option (RED RAVEN)
Added Avid DNxHD/HR SQ codec recording standalone option (RED RAVEN)
Added R3D + DNxHD/HR HQ codec recording option (RED RAVEN)
Added R3D + DNxHD/HR SQ codec recording option (RED RAVEN)
Added 30.00 fps project time base
Added Kippertie ND Lens Mount (KipperTie Revolva) support
Added Zeiss XD Metadata Support: Implemented extended Cooke /i commands for lens shading and distortion for metadata captured from Zeiss lenses (included in R3D metadata)
Added Teradek Bolt DSMC2 module support
Added Sigma Art lens for Nikon support
Added Sigma lens firmware v2.01 support
Added Sigma 50-100mm F1.8 DC HSM Art Lens for Canon support
Added Sigma 14-24mm f/2.8 DG HSM Art for Canon support
Added Sigma 105mm f/1.4 DG HSM Art for Canon support
Added Sigma 14mm f/1.8 DG HSM Art for Canon support
Added Sigma 70mm f/2.8 DG Macro Art for Canon support
Added AF-S Nikkor 70-200mm f/2.8G ED VR II support
Improved UI responsiveness
Improved pixel processing along high contrast edges
Improved user error messages
Fixed camera startup issues that occurred with some batteries
Fixed hot pixels that appeared after using Auto Calibration
Fixed vertical lines displayed when changing resolution, magnify or playback with a RED Touch 4.7" LCD
Fixed DSMC2 Side Handle lock feature
Fixed potential errors associated with R3D+ProRes
Fixed camera freeze when Auto Focus 'fast' mode selected
Fixed Camera Info displayed for Scarlet-W Monochrome
Fixed DSMC2 Sidekick navigation using vertical spinner
Fixed Gamma Space preset always defaulting to REDgamma 4
Fixed incorrect upper status bar aperture values in Playback
Fixed loss of SYNC OUT after toggling 'Reduced Judder Preview'
Fixed monitor artifacts toggling HDRx in 6K 6:5 with Lookaround
Fixed quick flash on LCD when double-tapping LCD to exit Clean mode
Fixed camera freeze after loading 3D LUT files
Fixed slate parameters in playback
Fixed camera freeze using DSMC2 Side Handle to focus
Fixed SYNC failure after 'Genlock' selected with genlock device connected on startup
Fixed test audio tone when camera is genlocked
Fixed tethered REDMOTE detection of lost connection
Fixed timecode overlay in playback after pressing REC button twice
Fixed read out-of-focus peaking high contrast edge
Fixed shutter angle spinner when setting above 90 degrees
Fixed calibration export for EPIC-W GEMINI 5K S35
Fixed camera crashing after selecting "Unknown" from search results
Fixed incorrect f-stop limit displayed for some lenses
Fixed histogram to display full range in ACES mode
Fixed Genlock Offset text box to display all characters
Fixed ISO in RAW mode for GEMINI sensor
Fixed Yellow Cal indicator in Auto Cal mode
Fixed split screen on Magnify with 4K FF and Lookaround enabled
Fixed camera freeze attaching a lens during record
Fixed intermittent LAN connection on startup
Fixed focus control using DSMC2 Side Handle
Fixed 'Confirm' style dropdown list in Focus > Mode dialog
Fixed aperture lockout using a variable aperture zoom lens
Fixed playback video corruption with 8K 6:5 ANA clip
Fixed shortcut name of _0 when Settings > Attached Modules is mapped
Fixed Gamma Space preset defaulting to REDgamma4
Fixed GEMINI corrupted image in 4.5K 4:1/8:1 with Lookaround enabled
Fixed inconsistent lens hot swap detection
Fixed blank screen for extended period when loading a large clip in Playback
Fixed intermittent diagonal tear on RED Touch 4.7" and RED Touch 7" LCD
Fixed incorrect overlay mode after selecting clean mode and restarting camera
Fixed intermittent RAVEN camera freeze with auto calibration
Fixed overlay shift on RED Touch 9" LCD
Fixed scrolling video on LCD in 5K FF and Framed Overlay enabled
Fixed flashing pixels in sensor flip mode
Fixed Infrastructure Mode SSID Scan button in Playback
Fixed camera shutdown entering playback of 2K 2:1 Apple ProRes clip
Fixed invalid 'Image Stabilization Not Supported' notification
Fixed camera freeze loading large ProRes clip in Playback
Fixed 'Unknown Unknown' resolution displayed in Playback with no media
Fixed Frame Guide displayed on HDMI monitor with 'Auto Hide Menus' enabled
Fixed artifacts displayed on the monitor in Playback when switching between clips
Fixed colored bands displayed on the monitor in 2K FF, 1.3x, ProRes 4444 at 60 fps
Fixed image roll on specific camera formats with 'Framed Overlay' enabled
Fixed scrolling image in Magnify with 2K 6:5 2x format
Fixed frame rate changing when entering Magnify
Fixed SDI video scrolling at 60Hz with 'Framed Overlay' enabled
Fixed camera shutdown after upgrade with auto calibration enabled
Fixed display preset in Legacy mode with False Color enabled
Fixed Exposure Tool in Legacy mode
Fixed invalid Time Indicator with fully charged battery
Fixed N/A Power Indicator with non-RED battery when set to Time Remaining
Changed IPP2 to be the default image pipeline (Output Tone Map: Low, Highlight Roll-off: Soft)
Removed Avid DNxHR LB codec

OPERATIONAL NOTES SPECIFIC TO BUILD v7.1.0.1

Perform sensor calibration after upgrade.
Refer to https://support.red.com/hc/en-us/sections/204939547 for the list of Known Issues
Secure Format media before using Pre-Record.
The horizon feature requires Gyro calibration be completed prior to use.
Do not 3D sync when GEN ICON is not illuminated or yellow.
Image Magnify is available during preview only.
HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

VERSION 7.0.4

23.3 MB

Release Date:

8/9/2018

Release Notes

DSMC2 Release Build v7.0.4 August 9, 2018

IMPORTANT:

You cannot downgrade a DSMC2, EPIC-W, SCARLET-W or REDRAVEN to earlier than v7.0.1.7 after upgrading to v7.0.4.
You must upgrade your REDMOTE firmware to v9.7.×. Download the firmware upgrade from red.com/downloads.
Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
Preset files created only on v4.0.x or later are compatible with v7.0.4.
It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.
Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

UPGRADEDSMCFIRMWARE TO v7.0.4

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v7.0.3

Fixed rare occurrence of horizontal green lines in recording on GEMINI
Fixed camera freeze attaching a lens during record
Fixed lens detection with SIGMA v2.0.1 lens firmware
Fixed CDL saturation not being properly applied
Fixed exposure tools after the LCD is detached/attached
Fixed loss of iris control on SIGMA 18-35mm for Canon
Fixed ‘Proxy Buffer Overflow’ with 4K R3D + Apple ProRes and HDRx
Fixed UI Flip for LCD/EVF port
Fixed playback video corruption with 8K 6:5 ANA clip
Fixed focus control using DSMC2 Side Handle
Fixed Gamma Space preset defaulting to REDgamma4
Fixed intermittent LAN connection on startup
Fixed all white RED Touch 7" LCD on camera power up
Enhanced user error messages
Removed 30Hz Frequency option for RED Touch 4.7" and 7" LCD

OPERATIONALNOTESSPECIFIC TO BUILD v7.0.4

Perform sensor calibration after upgrade.
Secure Format media before using Pre-Record.
The horizon feature requires Gyro calibration be completed prior to use.
Do not 3D sync when GENICON is not illuminated or yellow.
Image Magnify is available during preview only.
HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

VERSION 7.0.3

23.3 MB

Release Date:

5/21/2018

Release Notes

DSMC2 Release Build v7.0.3 May 21, 2018

IMPORTANT:

You cannot downgrade a DSMC2, EPIC-W, SCARLET-W or REDRAVEN to earlier than v7.0.1.7 after upgrading to v7.0.3.
You must upgrade your REDMOTE firmware to v9.7.×. Download the firmware upgrade from red.com/downloads.
Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
Preset files created only on v4.0.x or later are compatible with v7.0.3.
It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.
Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

UPGRADEDSMCFIRMWARE TO v7.0.3

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v7.0.2

Added DSMC2 BRAIN support
Updated WEAPON camera name to DSMC2 in Camera Info
Updated all camera names to include sensor info
Fixed vertical lines displayed on a RED Touch 4.7" LCD when changing resolution, magnify or playback
Fixed incorrect f-stop limits for some lenses
Fixed histogram to display full range in ACES mode

OPERATIONALNOTESSPECIFIC TO BUILD v7.0.3

Perform sensor calibration after upgrade.
Secure Format media before using Pre-Record.
The horizon feature requires Gyro calibration be completed prior to use.
Do not 3D sync when GENICON is not illuminated or yellow.
Image Magnify is available during preview only.
HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

VERSION 7.0.2

23.3 MB

Release Date:

4/19/2018

Release Notes

DSMC2 Release Build v7.0.2 April 19, 2018

IMPORTANT:

You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v7.0.2 after upgrading to v7.0.2.
You must upgrade your REDMOTE firmware to v9.7.×. Download the firmware upgrade from red.com/downloads.
Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
Preset files created only on v4.0.x or later are compatible with v7.0.2.
It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.
Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

UPGRADEDSMCFIRMWARE TO v7.0.2

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v7.0.1

Improved REDMINI-MAG® reliability
Added DSMC2® GEMINI™ support
Fixed camera crash in playback after changing control surface
Fixed 2K 6:5 distorted image after toggling HDRx with Lookaround
Fixed intermittent audio anomalies in recording
Fixed Stop Lights based on RAW data
Fixed distorted image in playback on HELIUM camera using preset with flip/mirror enabled
Fixed diagonal tearing of RED Touch 7" or RED Touch 4.7" LCD
Fixed camera freeze and/or shutdown after WiFi connection
Fixed Legacy ACES to use restricted (legal) range
Fixed incorrect LUT applied with ACES and 3D LUT preset
Fixed VU meter accuracy in playback with 4 channel audio
Fixed 6K 6:5 distorted image in playback
Fixed focus mode locked on RACK when toggling thru settings
Fixed loss of UI control on top LCD after switching to clean
Fixed blue tint with Motion Mount and IPP2 for HELIUM or MONSTRO based cameras
Fixed power information on UI when Jetpack attached
Fixed EVF port hot plug with no HDMI port on attached module
Fixed aperture control with Sigma lens
Fixed Focal Length displayed in UI when using Element Technica protocol
Fixed relative shutter angle with Reduce Judder Preview
Fixed camera response slowdown in AF Continuous mode
Fixed monitor artifacts when the Global Flip/Mirror feature is enabled
Fixed intermittent camera HD-SDI output on startup
Fixed RTC battery discharge rate when powered off
Fixed all HDR display presets to use restricted (legal) range
Fixed 3D LUT input to be REDLogFilm based
Fixed intermittent locking of Flanders DM-series monitors
Fixed horizontal tear on startup at 2K 2:1 119.88fps with HDRx
Fixed incorrect values after importing an RCX Look preset
Updated DSMC2® GEMINI™ 5K 6:5 format to use full sensor height (3600×3000)

OPERATIONALNOTESSPECIFIC TO BUILD v7.0.2

Perform sensor calibration after upgrade.
Secure Format media before using Pre-Record.
The horizon feature requires Gyro calibration be completed prior to use.
Do not 3D sync when GENICON is not illuminated or yellow.
Image Magnify is available during preview only.
HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

VERSION 6.3.106

15.5 MB

Release Date:

12/21/2017

Release Notes

DSMC2 Release Build v6.3.106 December 21, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.105 or v7.0.0 after upgrading to v6.3.106.
You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
Preset files created only on v4.0.x or later are compatible with v6.3.106.
It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.106

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.105

Fixed blue tint with Standard OLPF and Motion Mount
Fixed full SLA notification to always display on top
Fixed distorted display with 7.5K formats and MONSTRO 8K VV camera

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.106

Secure Format media before using Pre-Record.
The horizon feature requires Gyro calibration be completed prior to use.
Do not 3D sync when GENICON is not illuminated or yellow.
Image Magnify is available during preview only.
HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

VERSION 7.0.1

23.1 MB

Release Date:

12/15/2017

Release Notes

DSMC2 Release Build v7.0.1 December 15, 2017

IMPORTANT:

You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.105 or v7.0.0 after upgrading to v7.0.1.
You must upgrade your REDMOTE firmware to v9.7.×. Download the firmware upgrade from red.com/downloads.
Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
Preset files created only on v4.0.x or later are compatible with v7.0.1.
It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.
Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

UPGRADEDSMCFIRMWARE TO v7.0.1

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v7.0.0

Added support for future RED accessories
Fixed Apple ProRes elevated black levels in IPP2 mode
Fixed camera freeze after loading a large number of 3D LUTs
Fixed camera response slowdown in AF Continuous mode
Fixed delay entering playback with a Creative 3D LUT
Fixed False Color levels in IPP2 mode
Fixed Gio Scope False Color mapping in IPP2 mode
Fixed incorrect Gamma Curve listed in the Output Summary
Fixed intermittent high fan speed during camera shutdown or entering playback
Fixed Error 0×0000020 when starting record immediately after changing frame rate
Fixed Error 0×0000020 in HDRX mode at 1 fps and REDCODE 3:1
Fixed intermittent ‘Audio Buffer Overflow’ errors with Apple ProRes
Fixed several ‘Proxy Buffer Overflow’ error conditions during recording
Fixed bleached out image while lens focus is adjusted with auto focus
Fixed intermittent Power Status indicator with DSMC2 Jetpack Expander
Fixed issues with enabling/disabling Output Sharpness
Fixed loss of HDRx setting after power cycle
Fixed MXF ‘Picture Essence Descriptor’ for Avid DNxHD/HR 444
Fixed R3D playback (Legacy RWG/L3G10) levels to match preview
Fixed Record Start/Stop sounds enable
Fixed full SLA notification to always be on top
Fixed intermittent MOTIONMOUNT ND operation
Fixed scrolling image when 3.5K FF clip is loaded for playback with MONSTRO 8K VV
Fixed Red stop light response at higher ISO
Improved handling for active file transfers with remote control application
Improved record start response time

OPERATIONALNOTESSPECIFIC TO BUILD v7.0.1

Secure Format media before using Pre-Record.
The horizon feature requires Gyro calibration be completed prior to use.
Do not 3D sync when GENICON is not illuminated or yellow.
Image Magnify is available during preview only.
HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

VERSION 6.3.105

15.5 MB

Release Date:

10/5/2017

Release Notes

DSMC Release Build v6.3.105 October 5, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.105.
You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.105.
You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.105.
You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.105 or v7.0.0 after upgrading to v6.3.105.
You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
Preset files created only on v4.0.x or later are compatible with v6.3.105.
It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.105

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.104

Fixed dismount method for 960GB REDMINI-MAG

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.105

Secure Format media before using Pre-Record.
The horizon feature requires Gyro calibration be completed prior to use.
Do not 3D sync when GENICON is not illuminated or yellow.
Image Magnify is available during preview only.
HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

VERSION 7.0.0

23 MB

Release Date:

10/5/2017

Release Notes

DSMC2 Release Build v7.0.0 October 5, 2017

IMPORTANT:

You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.105 or v7.0.0 after upgrading to v7.0.0.
You must upgrade your REDMOTE firmware to v9.7.×. Download the firmware upgrade from red.com/downloads.
Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
Preset files created only on v4.0.x or later are compatible with v7.0.0.
It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.
Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

UPGRADEDSMCFIRMWARE TO v7.0.0

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.105

Added WEAPONMONSTRO 8K VV support
Added WEAPONHELIUM 8K S35 MONOCHROME support
Added IPP2 support for HELIUM 8K S35 and MONSTRO 8K VV cameras
Added Tethering support for HELIUM 8K S35 and MONSTRO 8K VV cameras
Added UDF filesystem support
Added >4GB Apple ProRes file support (UDF only)
Added Varispeed audio support
Added baked-in 3D LUT controls for Apple ProRes and Avid DNxHD/HR
Added per monitor 3D LUT status to RED Standard Overlay
Added splash screen on startup
Added RAW/Log View indicator to playback overlay
Added IPP2 CreativeCube 3D LUT metadata
Added 3D LUT support in playback (IPP2 only)
Added IP Address display to WiFi Ad-Hoc Mode
Added R3D User Metadata
Added new ISO calibration for HELIUM 8K S35 cameras
Added ‘Use new ISO Calibration’ checkbox for HELIUM 8K S35 cameras (Enabled by default)
Added log_files directory
Added clip name as prefix to exported LUT filename
Added notification when auto calibration is loading
Added Sigma ART lens support
Added Canon CN-E 18-80mm support

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v7.0.0rc4

Added WEAPONMONSTRO 8K VV support
Added Canon CN-E 18-80mm support
Added Sigma ART lens support
Added WEAPONHELIUM 8K S35 MONOCHROME help files
Fixed ‘Buffer Overflow’ error during record with RFTP operation
Fixed ‘Error 0×000000e8’ at 3K FF 120fps with R3D + DNxHD/HR
Fixed HDMI initialization on startup when top LCD is OFF
Fixed incorrect 3D LUT name with tethering enabled
Fixed lower status bar power label for the TILTA Expander
Fixed magnify at low frame rates
Fixed RED Touch 4.7" display behavior on startup
Fixed stream type field for 3D LUT streaming
Fixed dismount method for RED 960GB MINIMAG

OPERATIONALNOTESSPECIFIC TO BUILD v7.0.0

Secure Format media before using Pre-Record.
The horizon feature requires Gyro calibration be completed prior to use.
Do not 3D sync when GENICON is not illuminated or yellow.
Image Magnify is available during preview only.
HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

VERSION 6.3.104

15.5 MB

Release Date:

8/30/2017

Release Notes

DSMC Release Build v6.3.104 August 30, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.104.
You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.104.
You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.104.
You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.98 or v6.4.21 after upgrading to v6.3.104.
You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
Preset files created only on v4.0.x or later are compatible with v6.3.104.
It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.104

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.102

Added rear module upgrade failure notification
Fixed RED Touch 4.7" LCD operation attached to side LCD/EVF port (DSMC2 only)
Fixed SDI output on startup with framed overlay (DSMC2 only)
Fixed intermittent media mount failure (DSMC2 only)
Fixed gamma correction for RED Touch 7" LCD and DSMC2 EVF (DSMC2 only)
Fixed ‘Proxy Buffer overflow’ with 4K HD R3D+DNxHR/HD (DSMC2 only)
Fixed intermittent OMOD module firmware upgrade failure (DSMC2 only)
Fixed Serial Communication dialog for OMOD RT modules (DSMC2 only)
Fixed Amps in ‘Power Out’ for the DSMC2 V-Lock Battery Module Pro (DSMC2 only)
Fixed camera shutdown with REDLINK Bridge Module attached (DSMC only)
Fixed no LCD image on startup connected to Pro IO LCD/EVF port (DSMC only)
Fixed displayed clip name of -- after exiting playback
Fixed displayed Frame Rate after Project Time Base is changed
Updated 8K VV calibration

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.104

Secure Format media before using Pre-Record.
The horizon feature requires Gyro calibration be completed prior to use.
Do not 3D sync when GENICON is not illuminated or yellow.
Image Magnify is available during preview only.
HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

VERSION 6.3.102

15.4 MB

Release Date:

6/1/2017

Release Notes

DSMC Release Build v6.3.102 June 1, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.102.
You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.102.
You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.102.
You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.98 or v6.4.21 after upgrading to v6.3.102.
You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
Preset files created only on v4.0.x or later are compatible with v6.3.102.
It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.102

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.101

Added future RED accessory support
Fixed Aperture scroll bar in the Lens Info dialog after lens swap
Fixed incorrect clip list after media is formatted
Fixed Apple ProRes ‘Buffer Overflow Error’ with 8K at 60fps
Fixed ’Buffer Overflow ’ error with Avid DNx444 at high frame rate

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.102

Secure Format media before using Pre-Record.
The horizon feature requires Gyro calibration be completed prior to use.
Do not 3D sync when GENICON is not illuminated or yellow.
Image Magnify is available during preview only.
HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

VERSION 6.3.101

15.4 MB

Release Date:

4/18/2017

Release Notes

DSMC Release Build v6.3.101 April 18, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.101.
You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.101.
You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.101.
You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.98 or v6.4.21 after upgrading to v6.3.101.
You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
Preset files created only on v4.0.x or later are compatible with v6.3.101.
It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.101

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.98

Added log_files directory
Fixed HELIUM horizontal lines in image after calibration (DSMC2 only)
Fixed Avid DNxHD/HR SQ quality (DSMC2 only)
Fixed 8K HD record error at high frame rate (DSMC2 only)
Fixed 25/50Hz HD-SDI output with test patterns or playback (DSMC2 only)
Fixed missing timecode and frame rate in extended_clipinfo_t for ProRes and MXF clips (DSMC2 only)
Fixed audio buffer oveflow errors with Apple ProRes 422/422LT (DSMC2 only)
Fixed tearing in R3D for 3.5K 5:4 2x Anamorphic mode (DSMC2 only)
Fixed Side Handle detection on startup (DSMC2 only)
Fixed RCPMEDGCII response on record stop
Fixed blank REDTOUCH 4.7" LCD after systems restore or upgrade
Fixed calibration rename failure with special characters
Fixed camera freeze applying guides in playback
Improved HELIUM calibration (DSMC2 only)

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.101

Secure Format media before using Pre-Record.
The horizon feature requires Gyro calibration be completed prior to use.
Do not 3D sync when GENICON is not illuminated or yellow.
Image Magnify is available during preview only.
HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.