DSMC2 AND WEAPON FIRMWARE

DSMC2 Release Build v7.3.0 December 17, 2019

NOTE: Download the latest versions of REDCINE-X PRO and the RED ROCKET Installer or the RED ROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade the camera to earlier than v7.0.2 after upgrading to v7.3.0.
• You must upgrade your REDMOTE firmware to v9.7.x. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225544547 for supported Canon lenses.
• Refer to https://support.red.com/hc/en-us/articles/225724728 for supported Nikon lenses.
• Refer to https://support.red.com/hc/en-us/articles/225565627 for supported PL lenses.
• Preset files created only on v4.0.x or later are compatible with v7.3.0.
• User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADE DSMC2 FIRMWARE TO v7.3.0

1. 1. Connect a RED MINI-MAG to your computer.
2. 2. Download the most recent firmware from www.red.com/downloads.
3. 3. Unzip the firmware zip file.
4. 4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.
5. 5. Eject or unmount the SSD, and then remove the SSD.
6. 6. Ensure the camera is powered down.
7. 7. Insert the SSD with the force_upgrade folder into your camera.
8. 8. Power up the camera.

   The upgrade automatically runs at power up. During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

9. 9. After the camera powers down, remove the SSD and wait 10 seconds.
10. 10. Power up the camera.

    The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

11. 11. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.
12. 12. Reformat the SSD before recording to it.

SIGNIFICANT CHANGES SINCE PREVIOUS BUILD v7.2.4

• Added DSMC2 Dragon-X 6K support
• Fixed intermittent HD-SDI output with V-Lock IO Expander
• Fixed playback color in low light scenes
• Fixed horizontal lines on startup with DSMC2 RED TOUCH 7.0" LCD

OPERATIONAL NOTES SPECIFIC TO BUILD v7.3.0

• Perform sensor calibration after upgrade.
• Refer to https://support.red.com/hc/en-us/sections/204939547 for the list of Known Issues.
• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GEN ICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright (c) 2004-2019 RED.COM, LLC. All Rights Reserved.

DSMC2 Release Build v7.2.4 June 22, 2019

NOTE: Download the latest versions of REDCINE-X PRO and the RED ROCKET Installer or the RED ROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade the camera to earlier than v7.0.2 after upgrading to v7.2.4.
• You must upgrade your REDMOTE firmware to v9.7.x. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225544547 for supported Canon lenses.
• Refer to https://support.red.com/hc/en-us/articles/225724728 for supported Nikon lenses.
• Refer to https://support.red.com/hc/en-us/articles/225565627 for supported PL lenses.
• Preset files created only on v4.0.x or later are compatible with v7.2.4.
• User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMC2FIRMWARE TO BUILD v7.2.4

1. 1. Connect a RED MINI-MAG to your computer.
2. 2. Download the most recent firmware from www.red.com/downloads.
3. 3. Unzip the firmware zip file.
4. 4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.
5. 5. Eject or unmount the SSD, and then remove the SSD.
6. 6. Ensure the camera is powered down.
7. 7. Insert the SSD with the force_upgrade folder into your camera.
8. 8. Power up the camera.

   The upgrade automatically runs at power up. During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

9. 9. After the camera powers down, remove the SSD and wait 10 seconds.
10. 10. Power up the camera.

    The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

11. 11. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.
12. 12. Reformat the SSD before recording to it.

SIGNIFICANT CHANGES SINCE PREVIOUS BUILD v7.2.2

• Added Core SWX EVO Module support
• Fixed DSMC2 EVF color mismatch with IPP2
• Fixed banding artifacts with MONSTRO when Sensor Flip/Mirror Scan Direction enabled
• Fixed Apple ProRes file metadata for Rec. 2020
• Fixed Apple ProRes output transform with Rec. 2020 baked-in settings
• Change to only display voltage for all Gold Mount batteries

OPERATIONAL NOTES SPECIFIC TO BUILD v7.2.4

• Perform sensor calibration after upgrade.
• Refer to https://support.red.com/hc/en-us/sections/204939547 for the list of Known Issues.
• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GEN ICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright (c) 2004-2019 RED.COM, LLC. All Rights Reserved.

DSMC2 Release Build v7.2.2 April 25, 2019

NOTE: Download the latest versions of REDCINE-X PRO and the RED ROCKET Installer or the RED ROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade the camera to earlier than v7.0.2 after upgrading to v7.2.2.
• You must upgrade your REDMOTE firmware to v9.7.x. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225544547 for supported Canon lenses.
• Refer to https://support.red.com/hc/en-us/articles/225724728 for supported Nikon lenses.
• Refer to https://support.red.com/hc/en-us/articles/225565627 for supported PL lenses.
• Preset files created only on v4.0.x or later are compatible with v7.2.2.
• User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v7.2.2

1. Connect a RED MINI-MAG to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

6. Ensure the camera is powered down.

7. Insert the SSD with the force_upgrade folder into your camera.

8. Power up the camera.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

9. After the camera powers down, remove the SSD and wait 10 seconds.

10. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

11. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

12. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v7.2.1

• Updated DSMC2 Production Module support

OPERATIONALNOTESSPECIFIC TO BUILD v7.2.2

• Perform sensor calibration after upgrade.
• Refer to https://support.red.com/hc/en-us/sections/204939547 for the list of Known Issues
• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GEN ICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2019 RED.COMLLC. All Rights Reserved.

DSMC2 Release Build v7.2.0 January 31, 2019

NOTE: Download the latest versions of REDCINE-X PRO and the RED ROCKET Installer or the RED ROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade a DSMC2, WEAPON, EPIC-W, SCARLET-W or RED RAVEN to earlier than v7.0.2 after upgrading to v7.2.0.
• You must upgrade your REDMOTE firmware to v9.7.x. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience Side Handle issues after upgrading.
• Preset files created only on v4.0.x or later are compatible with v7.1.0b7.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v7.2.0

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v7.1.0.1

• Added DSMC2 Production Module (V-LOCK) support
• Added DSMC2 Touch 7.0" Ultra-Brite LCD support
• Fixed starting timecode mismatch of R3D and Proxy clip
• Fixed missing audio in ProRes clip with Reduce Judder Preview enabled
• Fixed intermittent auto calibration failure with DSMC2 MONSTRO 8K VV
• Fixed the blinking Power LED when using a third-party battery with the DSMC2 V-Lock I/O Expander
• Fixed ISO inaccuracy with DSMC2 GEMINI 5K S35 and the H2O OLPF
• Fixed the color shift in Preview with a Frame Summing selection of 4 or more
• Fixed the goal posts in Playback to match Preview
• Fixed incorrect Baked-in Settings displayed during Playback (Menu > Image > Image Pipeline > Output Summary)
• Fixed incorrect Baked-in Settings displayed after changing the Output Color Space (Menu > Image > Image Pipeline)
• Fixed Bar and Pie Focus Modes not updating properly

OPERATIONALNOTESSPECIFIC TO BUILD v7.2.0

• Perform sensor calibration after upgrade.
• Refer to https://support.red.com/hc/en-us/sections/204939547 for the list of Known Issues
• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GEN ICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2019 RED.COMLLC. All Rights Reserved.

DSMC2 Release Build v7.1.0.1                              November 27, 2018

NOTE: Download the latest versions of REDCINE-X PRO and the RED ROCKET Installer or the RED ROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade a camera to earlier than v7.0.2 after upgrading to v7.1.0.1.
• You must upgrade your REDMOTE firmware to v9.7.x. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225544547 for supported Canon lenses.
• Refer to https://support.red.com/hc/en-us/articles/225724728 for supported Nikon lenses.
• Refer to https://support.red.com/hc/en-us/articles/225565627 for supported PL lenses.
• Preset files created only on v4.0.x or later are compatible with v7.1.0.1.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADE DSMC2 FIRMWARE TO v7.1.0.1

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (RED MINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANT CHANGES SINCE PREVIOUS BUILD v7.0.4

• Added DSMC2 BRAIN support
• Added Sensor Flip/Mirror Scan Direction for DSMC2 MONSTRO 8K VV
• Added User-Defined Voltage Alert 
• Added focus peaking tool
• Added ability to import CDLs, RMDs, and LUTs
• Added 5K 4:3 and 5K 4:3 2x ANA support to EPIC-W 8K S35, DSMC2 8K S35 and DSMC2 8K VV
• Added option to select a center mark dot (small/medium + color)
• Added Hybrid Log-Gamma display preset 
• Added Avid DNxHD/HR HQ codec recording standalone option (RED RAVEN)
• Added Avid DNxHD/HR SQ codec recording standalone option (RED RAVEN)
• Added R3D + DNxHD/HR HQ codec recording option (RED RAVEN)
• Added R3D + DNxHD/HR SQ codec recording option (RED RAVEN)
• Added 30.00 fps project time base 
• Added Kippertie ND Lens Mount (KipperTie Revolva) support 
• Added Zeiss XD Metadata Support: Implemented extended Cooke /i commands for lens shading and distortion for metadata captured from Zeiss lenses (included in R3D metadata)
• Added Teradek Bolt DSMC2 module support 
• Added Sigma Art lens for Nikon support
• Added Sigma lens firmware v2.01 support
• Added Sigma 50-100mm F1.8 DC HSM Art Lens for Canon support
• Added Sigma 14-24mm f/2.8 DG HSM Art for Canon support
• Added Sigma 105mm f/1.4 DG HSM Art for Canon support
• Added Sigma 14mm f/1.8 DG HSM Art for Canon support
• Added Sigma 70mm f/2.8 DG Macro Art for Canon support
• Added AF-S Nikkor 70-200mm f/2.8G ED VR II support
• Improved UI responsiveness
• Improved pixel processing along high contrast edges
• Improved user error messages
• Fixed camera startup issues that occurred with some batteries
• Fixed hot pixels that appeared after using Auto Calibration
• Fixed vertical lines displayed when changing resolution, magnify or playback with a RED Touch 4.7" LCD 
• Fixed DSMC2 Side Handle lock feature 
• Fixed potential errors associated with R3D+ProRes
• Fixed camera freeze when Auto Focus 'fast' mode selected 
• Fixed Camera Info displayed for Scarlet-W Monochrome 
• Fixed DSMC2 Sidekick navigation using vertical spinner 
• Fixed Gamma Space preset always defaulting to REDgamma 4
• Fixed incorrect upper status bar aperture values in Playback 
• Fixed loss of SYNC OUT after toggling 'Reduced Judder Preview' 
• Fixed monitor artifacts toggling HDRx in 6K 6:5 with Lookaround 
• Fixed quick flash on LCD when double-tapping LCD to exit Clean mode 
• Fixed camera freeze after loading 3D LUT files 
• Fixed slate parameters in playback 
• Fixed camera freeze using DSMC2 Side Handle to focus 
• Fixed SYNC failure after 'Genlock' selected with genlock device connected on startup 
• Fixed test audio tone when camera is genlocked 
• Fixed tethered REDMOTE detection of lost connection 
• Fixed timecode overlay in playback after pressing REC button twice 
• Fixed read out-of-focus peaking high contrast edge 
• Fixed shutter angle spinner when setting above 90 degrees 
• Fixed calibration export for EPIC-W GEMINI 5K S35 
• Fixed camera crashing after selecting "Unknown" from search results
• Fixed incorrect f-stop limit displayed for some lenses
• Fixed histogram to display full range in ACES mode
• Fixed Genlock Offset text box to display all characters
• Fixed ISO in RAW mode for GEMINI sensor
• Fixed Yellow Cal indicator in Auto Cal mode
• Fixed split screen on Magnify with 4K FF and Lookaround enabled
• Fixed camera freeze attaching a lens during record
• Fixed intermittent LAN connection on startup
• Fixed focus control using DSMC2 Side Handle
• Fixed 'Confirm' style dropdown list in Focus > Mode dialog
• Fixed aperture lockout using a variable aperture zoom lens
• Fixed playback video corruption with 8K 6:5 ANA clip
• Fixed shortcut name of _0 when Settings > Attached Modules is mapped
• Fixed Gamma Space preset defaulting to REDgamma4
• Fixed GEMINI corrupted image in 4.5K 4:1/8:1 with Lookaround enabled
• Fixed inconsistent lens hot swap detection
• Fixed blank screen for extended period when loading a large clip in Playback
• Fixed intermittent diagonal tear on RED Touch 4.7" and RED Touch 7" LCD
• Fixed incorrect overlay mode after selecting clean mode and restarting camera
• Fixed intermittent RAVEN camera freeze with auto calibration
• Fixed overlay shift on RED Touch 9" LCD
• Fixed scrolling video on LCD in 5K FF and Framed Overlay enabled
• Fixed flashing pixels in sensor flip mode
• Fixed Infrastructure Mode SSID Scan button in Playback
• Fixed camera shutdown entering playback of 2K 2:1 Apple ProRes clip
• Fixed invalid 'Image Stabilization Not Supported' notification 
• Fixed camera freeze loading large ProRes clip in Playback
• Fixed 'Unknown Unknown' resolution displayed in Playback with no media
• Fixed Frame Guide displayed on HDMI monitor with 'Auto Hide Menus' enabled
• Fixed artifacts displayed on the monitor in Playback when switching between clips
• Fixed colored bands displayed on the monitor in 2K FF, 1.3x, ProRes 4444 at 60 fps
• Fixed image roll on specific camera formats with 'Framed Overlay' enabled
• Fixed scrolling image in Magnify with 2K 6:5 2x format
• Fixed frame rate changing when entering Magnify
• Fixed SDI video scrolling at 60Hz with 'Framed Overlay' enabled
• Fixed camera shutdown after upgrade with auto calibration enabled
• Fixed display preset in Legacy mode with False Color enabled
• Fixed Exposure Tool in Legacy mode
• Fixed invalid Time Indicator with fully charged battery
• Fixed N/A Power Indicator with non-RED battery when set to Time Remaining
• Changed IPP2 to be the default image pipeline (Output Tone Map: Low, Highlight Roll-off: Soft)
• Removed Avid DNxHR LB codec
• 
  

OPERATIONAL NOTES SPECIFIC TO BUILD v7.1.0.1

• Perform sensor calibration after upgrade.
• Refer to https://support.red.com/hc/en-us/sections/204939547 for the list of Known Issues
• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GEN ICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2018 RED.COM LLC. All Rights Reserved.

DSMC2 Release Build v7.0.4 August 9, 2018

IMPORTANT:

• You cannot downgrade a DSMC2, EPIC-W, SCARLET-W or REDRAVEN to earlier than v7.0.1.7 after upgrading to v7.0.4.
• You must upgrade your REDMOTE firmware to v9.7.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v7.0.4.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.
• Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

UPGRADEDSMCFIRMWARE TO v7.0.4

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v7.0.3

• Fixed rare occurrence of horizontal green lines in recording on GEMINI
• Fixed camera freeze attaching a lens during record
• Fixed lens detection with SIGMA v2.0.1 lens firmware
• Fixed CDL saturation not being properly applied
• Fixed exposure tools after the LCD is detached/attached
• Fixed loss of iris control on SIGMA 18-35mm for Canon
• Fixed ‘Proxy Buffer Overflow’ with 4K R3D + Apple ProRes and HDRx
• Fixed UI Flip for LCD/EVF port
• Fixed playback video corruption with 8K 6:5 ANA clip
• Fixed focus control using DSMC2 Side Handle
• Fixed Gamma Space preset defaulting to REDgamma4
• Fixed intermittent LAN connection on startup
• Fixed all white RED Touch 7" LCD on camera power up
• Enhanced user error messages
• Removed 30Hz Frequency option for RED Touch 4.7" and 7" LCD

OPERATIONALNOTESSPECIFIC TO BUILD v7.0.4

• Perform sensor calibration after upgrade.
• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2018 RED.COMLLC. All Rights Reserved.

DSMC2 Release Build v7.0.3 May 21, 2018

IMPORTANT:

• You cannot downgrade a DSMC2, EPIC-W, SCARLET-W or REDRAVEN to earlier than v7.0.1.7 after upgrading to v7.0.3.
• You must upgrade your REDMOTE firmware to v9.7.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v7.0.3.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.
• Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

UPGRADEDSMCFIRMWARE TO v7.0.3

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v7.0.2

• Added DSMC2 BRAIN support
• Updated WEAPON camera name to DSMC2 in Camera Info
• Updated all camera names to include sensor info
• Fixed vertical lines displayed on a RED Touch 4.7" LCD when changing resolution, magnify or playback
• Fixed incorrect f-stop limits for some lenses
• Fixed histogram to display full range in ACES mode

OPERATIONALNOTESSPECIFIC TO BUILD v7.0.3

• Perform sensor calibration after upgrade.
• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2018 RED.COMLLC. All Rights Reserved.

DSMC2 Release Build v7.0.2 April 19, 2018

IMPORTANT:

• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v7.0.2 after upgrading to v7.0.2.
• You must upgrade your REDMOTE firmware to v9.7.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v7.0.2.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.
• Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

UPGRADEDSMCFIRMWARE TO v7.0.2

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v7.0.1

• Improved REDMINI-MAG® reliability
• Added DSMC2® GEMINI™ support
• Fixed camera crash in playback after changing control surface
• Fixed 2K 6:5 distorted image after toggling HDRx with Lookaround
• Fixed intermittent audio anomalies in recording
• Fixed Stop Lights based on RAW data
• Fixed distorted image in playback on HELIUM camera using preset with flip/mirror enabled
• Fixed diagonal tearing of RED Touch 7" or RED Touch 4.7" LCD
• Fixed camera freeze and/or shutdown after WiFi connection
• Fixed Legacy ACES to use restricted (legal) range
• Fixed incorrect LUT applied with ACES and 3D LUT preset
• Fixed VU meter accuracy in playback with 4 channel audio
• Fixed 6K 6:5 distorted image in playback
• Fixed focus mode locked on RACK when toggling thru settings
• Fixed loss of UI control on top LCD after switching to clean
• Fixed blue tint with Motion Mount and IPP2 for HELIUM or MONSTRO based cameras
• Fixed power information on UI when Jetpack attached
• Fixed EVF port hot plug with no HDMI port on attached module
• Fixed aperture control with Sigma lens
• Fixed Focal Length displayed in UI when using Element Technica protocol
• Fixed relative shutter angle with Reduce Judder Preview
• Fixed camera response slowdown in AF Continuous mode
• Fixed monitor artifacts when the Global Flip/Mirror feature is enabled
• Fixed intermittent camera HD-SDI output on startup
• Fixed RTC battery discharge rate when powered off
• Fixed all HDR display presets to use restricted (legal) range
• Fixed 3D LUT input to be REDLogFilm based
• Fixed intermittent locking of Flanders DM-series monitors
• Fixed horizontal tear on startup at 2K 2:1 119.88fps with HDRx
• Fixed incorrect values after importing an RCX Look preset
• Updated DSMC2® GEMINI™ 5K 6:5 format to use full sensor height (3600×3000)

OPERATIONALNOTESSPECIFIC TO BUILD v7.0.2

• Perform sensor calibration after upgrade.
• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2018 RED.COMLLC. All Rights Reserved.

DSMC2 Release Build v6.3.106 December 21, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.105 or v7.0.0 after upgrading to v6.3.106.
• You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
• Preset files created only on v4.0.x or later are compatible with v6.3.106.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.106

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.105

• Fixed blue tint with Standard OLPF and Motion Mount
• Fixed full SLA notification to always display on top
• Fixed distorted display with 7.5K formats and MONSTRO 8K VV camera

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.106

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All Rights Reserved.

DSMC2 Release Build v7.0.1 December 15, 2017

IMPORTANT:

• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.105 or v7.0.0 after upgrading to v7.0.1.
• You must upgrade your REDMOTE firmware to v9.7.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v7.0.1.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.
• Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

UPGRADEDSMCFIRMWARE TO v7.0.1

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v7.0.0

• Added support for future RED accessories
• Fixed Apple ProRes elevated black levels in IPP2 mode
• Fixed camera freeze after loading a large number of 3D LUTs
• Fixed camera response slowdown in AF Continuous mode
• Fixed delay entering playback with a Creative 3D LUT
• Fixed False Color levels in IPP2 mode
• Fixed Gio Scope False Color mapping in IPP2 mode
• Fixed incorrect Gamma Curve listed in the Output Summary
• Fixed intermittent high fan speed during camera shutdown or entering playback
• Fixed Error 0×0000020 when starting record immediately after changing frame rate
• Fixed Error 0×0000020 in HDRX mode at 1 fps and REDCODE 3:1
• Fixed intermittent ‘Audio Buffer Overflow’ errors with Apple ProRes
• Fixed several ‘Proxy Buffer Overflow’ error conditions during recording
• Fixed bleached out image while lens focus is adjusted with auto focus
• Fixed intermittent Power Status indicator with DSMC2 Jetpack Expander
• Fixed issues with enabling/disabling Output Sharpness
• Fixed loss of HDRx setting after power cycle
• Fixed MXF ‘Picture Essence Descriptor’ for Avid DNxHD/HR 444
• Fixed R3D playback (Legacy RWG/L3G10) levels to match preview
• Fixed Record Start/Stop sounds enable
• Fixed full SLA notification to always be on top
• Fixed intermittent MOTIONMOUNT ND operation
• Fixed scrolling image when 3.5K FF clip is loaded for playback with MONSTRO 8K VV
• Fixed Red stop light response at higher ISO
• Improved handling for active file transfers with remote control application
• Improved record start response time

OPERATIONALNOTESSPECIFIC TO BUILD v7.0.1

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COMLLC. All Rights Reserved.

DSMC Release Build v6.3.105.1 October 19, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade a WEAPONMONSTRO 8K VV to earlier than v6.3.105.1 or v7.0.0 after upgrading to v6.3.105.1
• You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
• Preset files created only on v4.0.x or later are compatible with v6.3.105.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.105.1

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.105

• Added WEAPONMONSTRO 8K VV support

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.105.1

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All Rights Reserved.

DSMC2 Release Build v7.0.0 October 5, 2017

IMPORTANT:

• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.105 or v7.0.0 after upgrading to v7.0.0.
• You must upgrade your REDMOTE firmware to v9.7.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v7.0.0.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.
• Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

UPGRADEDSMCFIRMWARE TO v7.0.0

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.105

• Added WEAPONMONSTRO 8K VV support
• Added WEAPONHELIUM 8K S35 MONOCHROME support
• Added IPP2 support for HELIUM 8K S35 and MONSTRO 8K VV cameras
• Added Tethering support for HELIUM 8K S35 and MONSTRO 8K VV cameras
• Added UDF filesystem support
• Added >4GB Apple ProRes file support (UDF only)
• Added Varispeed audio support
• Added baked-in 3D LUT controls for Apple ProRes and Avid DNxHD/HR
• Added per monitor 3D LUT status to RED Standard Overlay
• Added splash screen on startup
• Added RAW/Log View indicator to playback overlay
• Added IPP2 CreativeCube 3D LUT metadata
• Added 3D LUT support in playback (IPP2 only)
• Added IP Address display to WiFi Ad-Hoc Mode
• Added R3D User Metadata
• Added new ISO calibration for HELIUM 8K S35 cameras
• Added ‘Use new ISO Calibration’ checkbox for HELIUM 8K S35 cameras (Enabled by default)
• Added log_files directory
• Added clip name as prefix to exported LUT filename
• Added notification when auto calibration is loading
• Added Sigma ART lens support
• Added Canon CN-E 18-80mm support

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v7.0.0rc4

• Added WEAPONMONSTRO 8K VV support
• Added Canon CN-E 18-80mm support
• Added Sigma ART lens support
• Added WEAPONHELIUM 8K S35 MONOCHROME help files
• Fixed ‘Buffer Overflow’ error during record with RFTP operation
• Fixed ‘Error 0×000000e8’ at 3K FF 120fps with R3D + DNxHD/HR
• Fixed HDMI initialization on startup when top LCD is OFF
• Fixed incorrect 3D LUT name with tethering enabled
• Fixed lower status bar power label for the TILTA Expander
• Fixed magnify at low frame rates
• Fixed RED Touch 4.7" display behavior on startup
• Fixed stream type field for 3D LUT streaming
• Fixed dismount method for RED 960GB MINIMAG

OPERATIONALNOTESSPECIFIC TO BUILD v7.0.0

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COMLLC. All Rights Reserved.

DSMC Release Build v6.3.105 October 5, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.105.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.105.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.105.
• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.105 or v7.0.0 after upgrading to v6.3.105.
• You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
• Preset files created only on v4.0.x or later are compatible with v6.3.105.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.105

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.104

• Fixed dismount method for 960GB REDMINI-MAG

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.105

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All Rights Reserved.

DSMC Release Build v6.3.104 August 30, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.104.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.104.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.104.
• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.98 or v6.4.21 after upgrading to v6.3.104.
• You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
• Preset files created only on v4.0.x or later are compatible with v6.3.104.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.104

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.102

• Added rear module upgrade failure notification
• Fixed RED Touch 4.7" LCD operation attached to side LCD/EVF port (DSMC2 only)
• Fixed SDI output on startup with framed overlay (DSMC2 only)
• Fixed intermittent media mount failure (DSMC2 only)
• Fixed gamma correction for RED Touch 7" LCD and DSMC2 EVF (DSMC2 only)
• Fixed ‘Proxy Buffer overflow’ with 4K HD R3D+DNxHR/HD (DSMC2 only)
• Fixed intermittent OMOD module firmware upgrade failure (DSMC2 only)
• Fixed Serial Communication dialog for OMOD RT modules (DSMC2 only)
• Fixed Amps in ‘Power Out’ for the DSMC2 V-Lock Battery Module Pro (DSMC2 only)
• Fixed camera shutdown with REDLINK Bridge Module attached (DSMC only)
• Fixed no LCD image on startup connected to Pro IO LCD/EVF port (DSMC only)
• Fixed displayed clip name of -- after exiting playback
• Fixed displayed Frame Rate after Project Time Base is changed
• Updated 8K VV calibration

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.104

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All Rights Reserved.

DSMC Release Build v6.3.102 June 1, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.102.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.102.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.102.
• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.98 or v6.4.21 after upgrading to v6.3.102.
• You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
• Preset files created only on v4.0.x or later are compatible with v6.3.102.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.102

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.101

• Added future RED accessory support
• Fixed Aperture scroll bar in the Lens Info dialog after lens swap
• Fixed incorrect clip list after media is formatted
• Fixed Apple ProRes ‘Buffer Overflow Error’ with 8K at 60fps
• Fixed ’Buffer Overflow ’ error with Avid DNx444 at high frame rate

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.102

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.

DSMC Release Build v6.3.101 April 18, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.101.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.101.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.101.
• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.98 or v6.4.21 after upgrading to v6.3.101.
• You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
• Preset files created only on v4.0.x or later are compatible with v6.3.101.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.101

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.98

• Added log_files directory
• Fixed HELIUM horizontal lines in image after calibration (DSMC2 only)
• Fixed Avid DNxHD/HR SQ quality (DSMC2 only)
• Fixed 8K HD record error at high frame rate (DSMC2 only)
• Fixed 25/50Hz HD-SDI output with test patterns or playback (DSMC2 only)
• Fixed missing timecode and frame rate in extended_clipinfo_t for ProRes and MXF clips (DSMC2 only)
• Fixed audio buffer oveflow errors with Apple ProRes 422/422LT (DSMC2 only)
• Fixed tearing in R3D for 3.5K 5:4 2x Anamorphic mode (DSMC2 only)
• Fixed Side Handle detection on startup (DSMC2 only)
• Fixed RCPMEDGCII response on record stop
• Fixed blank REDTOUCH 4.7" LCD after systems restore or upgrade
• Fixed calibration rename failure with special characters
• Fixed camera freeze applying guides in playback
• Improved HELIUM calibration (DSMC2 only)

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.101

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.

DSMC Release Build v6.3.98 April 12, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.98.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.98.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.98.
• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.98 or v6.4.21 after upgrading to v6.3.98.
• You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
• Preset files created only on v4.0.x or later are compatible with v6.3.98.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.98

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDSTATIONREDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.78

• Changed compatibility version (DSMC2 only)

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.98

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.

DSMC Release Build v6.3.78 February 3, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.78.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.78.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.78.
• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.2.64 or v6.3.47 after upgrading to v6.3.78.
• You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v6.3.78.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.78

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.75

• Added new IPP2 preview presets (DSMC2 only)
• Added TILTA Rear Module and Top Handle support (DSMC2 only)
• Fixed intermittent ‘FPGA upgrade failed’ message on startup (DSMC2 only)
• Fixed ‘Proxy Error’ when changing focus with Side Handle (DSMC2 only)
• Fixed line on bottom of frame when shooting high frame rates (DSMC2 only)
• Fixed in-camera playback with audio at 59.94 (DSMC2 only)
• Fixed Avid DNxHD/HR proxy record error (DSMC2 only)

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.78

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.

DSMC Release Build v6.3.75 January 10, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.75.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.75.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.75.
• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.2.64 or v6.3.47 after upgrading to v6.3.75.
• You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v6.3.75.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.75

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.74

• Added RED 480GB MINI-MAG support
• Added RED 960GB MINI-MAG support
• Fixed frame guide vertical alignment in UI flip/mirror mode

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.75

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.

DSMC Release Build v6.3.74 December 19, 2016

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.74.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.74.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.74.
• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.2.64 or v6.3.47 after upgrading to v6.3.74.
• You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v6.3.74.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.74

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.57

• Added ‘IPP2 Preview (RED)’ preset (DSMC2 HELIUM only)
• Added Canon EF 16-35mm f/2.8L IIIUSM lens support
• Added Canon EF 40mm STM lens support
• Added Canon EF-S 24mm STM lens support
• Fixed HELIUM calibration failure
• Fixed Proxy Record Error with R3D + Avid DNXHD/HR SQ (DSMC2 only)
• Fixed REDVOLT Expander battery detection status (DSMC2 only)
• Fixed HD-SDI timecode in ProRes playback (DSMC2 only)
• Fixed HELIUM Frame Averaging image artifacts (DSMC2 only)
• Fixed HELIUM magenta tint with standard OLPF (DSMC2 only)
• Fixed REDRAVEN horizontal line at high frame rate (DSMC2 only)
• Fixed shutter SYNC dropout (DSMC2 only)
• Fixed incorrect colors in ProRes playback (DSMC2 only)
• Fixed intermittent audio noise in Apple ProRes or Avid DNx clips (DSMC2 only)
• Fixed ‘Media Full’ indication recording Apple ProRes or Avid DNx (DSMC2 only)
• Fixed EPICDRAGONMONOCHROME limited Keys>Advanced options (DSMC only)
• Fixed control of Cooke lens v0.39 or earlier
• Fixed R3D playback hang using Next button
• Fixed ISO change lockout in ACES Proxy mode
• Fixed Ad Hoc SSID when camera ID changes
• Fixed Channel selection in Ad Hoc mode
• Fixed intermittent HD-SDI split screen at 60Hz
• Fixed manual exposure capability in Single Shot Mode
• Fixed 60Hz frequency option for all EVF types
• Fixed AE overlay exiting playback
• Changed WC Top Plate to ‘Easy Top’ in Module Status dialog (DSMC2 only)
• Changed maximum Frame Averaging count to 2 for all 8K cameras (DSMC2 only)
• Changed HELIUM internal default to LLO for 3rd party filter selection (DSMC2 only)
• Improved HELIUM image quality (DSMC2 only)
• Improved HELIUM sensor calibration (DSMC2 only)
• Improved DRAGON sensor calibration
• Improved Avid DNxHD/HR LB codec quality (DSMC2 only)
• Improved histogram scaling
• Improved UI spinner response time

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.74

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.

DSMC Release Build v6.3.57 December 8, 2016

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.57.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.57.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.57.
• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.2.64 or v6.3.38 after upgrading to v6.3.57.
• You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v6.3.57.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.57

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.27

• Added EPIC-W support
• Added Motion Mount support for HELIUM sensor
• Fixed WEAPONHELIUM intermittent startup failure (DSMC2 only)
• Fixed WEAPON 8K camera playback stutter (DSMC2 only)
• Fixed WEAPONHELIUM blackshade failure for exposures greater than 1/24 (DSMC2 only)
• Fixed WEAPONHELIUM HDRx X track exposure (DSMC2 only)
• Fixed Tethering support with Jetpack-SDI (DSMC2 only)
• Fixed HD-SDI output with genlock on startup (DSMC2 only)
• Fixed HD-SDI split screen at 60Hz (DSMC2 only)
• Fixed distorted image with 5.5K 4:1/8:1 with Lookaround (DSMC2 only)
• Fixed playback with 6K FF with Lookaround and QT 2K 4444XQ (DSMC2 only)
• Fixed image artifacts in 6K FF 2:1 and WS formats with lookaround and QT 4444 or 4444XQ (DSMC2 only)
• Fixed image artifacts in 7.5K WS format and QT 4444XQ (DSMC2 only)
• Fixed swapped audio channels on DSMC brain (DSMC only)
• Fixed blank LCD during magnify with REDCAST module (DSMC only)
• Fixed no REDCASTSDI out after reboot in AUTO mode (DSMC only)
• Fixed progress bar when secure formatting media (DSMC only)
• Fixed blue tint with Motion Mount and Standard OLPF (DSMC only)
• Fixed playback freeze with REDCAST and active genlock (DSMC only)
• Fixed REDCAST HD-SDI output after format change (DSMC only)
• Fixed diagonal tear with RED Touch 7" and 4.7" LCD
• Fixed image stutter on startup with RED Touch 9" LCD
• Fixed numerical value text in Audio Mixer UI
• Fixed stale spinner values after editing custom list
• Fixed non-functional left side record button in Still mode
• Fixed empty custom resolution list
• Fixed control of timecode out with LTC Out checkbox
• Fixed spinner when custom aperture value is added
• Fixed stale aperture metadata information in R3D
• Fixed black LCD screen with changing formats with Auto Hide enabled
• Fixed far focus distance value always equal to focus distance in metadata
• Fixed display priority with only EVF attached
• Fixed distance slider bar after ‘Init Lens’ operation
• Fixed clip duration time with pre-record

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.57

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.

DSMC Release Build v6.2.63 July 29, 2016

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.2.63.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.2.63.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.2.63.
• You cannot downgrade a WEAPON, SCARLET-W or REDRAVEN to earlier than v6.2.63 or v6.3.27 after upgrading to v6.2.63.
• You must upgrade your REDMOTE firmware to v9.5.×. Download the firmware upgrade from red.com/downloads.
• Refer to the REDDSMC Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v6.2.63.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.2.63

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDSTATIONREDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.2.60

• Added DSMC2 REDVOLT Expander support
• Added DSMC2 V-Lock Battery Module support
• Added DSMC2 JETPACK-SDI Expander support
• Added RED 512GB V6 support
• Fixed magnify issue with Apple ProRes 4444 and 444XQ (DSMC2 only)
• Fixed record start failure with HDRx at 2K WS 1fps
• Fixed invalid Power In information after battery swap

OPERATIONALNOTESSPECIFIC TO BUILD v6.2.63

• ProRes only playback is not supported
• Secure Format media before using Pre-Record.
• Please perform an Auto-Cal after upgrading from v6.1.6.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.

DSMC Release Build v6.3.27 July 29, 2016

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.27.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.27.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.27.
• You cannot downgrade a WEAPON, SCARLET-W or REDRAVEN to earlier than v6.2.63 or v6.3.27 after upgrading to v6.3.27.
• You must upgrade your REDMOTE firmware to v9.5.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v6.3.27.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.27

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.17

• Added 8K S35 HELIUM sensor support
• Added 8K VV DRAGON sensor support
• Added 8K VV Anamorphic DRAGON sensor support
• Added DSMC2 REDVOLT Expander support
• Added DSMC2 V-Lock Battery Module support
• Added DSMC2 JETPACK-SDI Expander support
• Added REDMOTE v9.6.28 (DSMC only)
• Added RED 512GB V6 support
• Fixed WEAPON 8K VV black sun artifact (DSMC2 only)
• Fixed Apple ProRes playback with 4 channels of audio (DSMC2 only)
• Fixed Apple ProRes playback audio synchronization (DSMC2 only)
• Fixed incorrect Apple ProRes frame rate in Open Gate mode (DSMC2 only)
• Fixed magnify issue with Apple ProRes 4444 and 444XQ (DSMC2 only)
• Fixed framed overlay/auto hide menus for mirrored monitor
• Fixed random cursor movement in playlist moving multiple clips
• Fixed camera freeze in playback with auto-hide menu and custom overlay
• Fixed blank RED Touch 7" LCD on startup
• Fixed record start failure with HDRx at 2K WS 1fps
• Fixed invalid Power In information after battery swap

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.27

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.

DSMC Release Build v6.3.17 June 23, 2016

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.17.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.17.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.17.
• You cannot downgrade a WEAPON CF to earlier than v6.1.52, v6.2.60 or v6.3.17 after upgrading to v6.3.17.
• You cannot downgrade a WEAPON MG, SCARLET-W or REDRAVEN to earlier than v6.2.60 or v6.3.17 after upgrading to v6.3.17.
• You must upgrade your REDMOTE firmware to v9.5.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v6.3.17.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.17

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.10

• Added WiFi static IP support for WEAPON and REDLINK Bridge
• Added RED 512GB V5 support
• Improved Nikon Iris control
• Fixed Apple ProRes and Avid DNxHD/HR audio in Open Gate mode (DSMC2 only)
• Fixed calibration ISO for WEAPON 6K STHOLPF (DSMC2 only)
• Fixed frame guides with playback and ProRes files (DSMC2 only)
• Fixed inability to playback ProRes file after an R3D clip (DSMC2 only)
• Fixed monitor output with 6K FF 1.25x ANA and Avid DNxHR/HD 4K mode (DSMC2 only)
• Fixed playback of 6K 3:2 1.3x ANA ProRes clips (DSMC2 only)
• Fixed intermittent media mount failure on startup or hot plug (DSMC2 only)
• Fixed HD-SDI stutter in R3D record mode (DSMC2 only)
• Fixed HD-SDI vertical scroll in 4K 3:2 1.3x ANA with Lookaround (DSMC2 only)
• Fixed playback screen with REDCAST after changing Output Mode (DSMC only)
• Fixed black image switching resolution with Avid DNx 444 (DSMC2 only)
• Fixed invalid battery status with ET battery modules (DSMC2 only)
• Fixed REDRAVEN black sun artifact (DSMC2 only)
• Fixed RED Touch 4.7" LCD diagonal tear exiting magnify
• Fixed RED Touch 4.7" LCD frozen screen entering magnify
• Fixed WiFi connect button when connecting/disconnecting
• Fixed 1 frame delay using Internal Timelapse Timer
• Fixed Canon Motion Mount ND operation
• Fixed Exposure Tool for ISO > 800
• Fixed Green and Blue curve adjustment values in R3D metadata
• Fixed max fan speed in adaptive modes
• Fixed Monitor priority list in UI
• Removed AWB in playback
• Removed genlock selection in Sensor Sync Mode dialog when no genlock input is present
• Removed genlock source selection for all WEAPON cameras (DSMC2 only)

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.17

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.

DSMC Release Build v6.2.60 June 23, 2016

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.2.60.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.2.60.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.2.60.
• You cannot downgrade a WEAPON CF to earlier than v6.1.52 or v6.2.60 after upgrading to v6.2.60.
• You cannot downgrade a WEAPON MG, SCARLET-W or REDRAVEN to earlier than v6.2.60 after upgrading to v6.2.60.
• You must upgrade your REDMOTE firmware to v9.5.×. Download the firmware upgrade from red.com/downloads.
• Refer to the REDDSMC Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v6.2.60.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.2.60

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDSTATIONREDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.2.57

• Added RED 512GB V5 support
• Fixed HD-SDI vertical scroll in 4K 3:2 1.3x ANA with Lookaround (DSMC2 only)
• Fixed HD-SDI stutter in R3D record mode (DSMC2 only)
• Fixed ‘ProRes Disabled’ check after media inserted (DSMC2 only)
• Fixed intermittent media mount failure on startup or hot plug (DSMC2 only)
• Fixed invalid battery status with ET battery modules (DSMC2 only)
• Fixed REDRAVEN black sun artifact (DSMC2 only)
• Fixed 1 frame delay using Internal Timelapse Timer
• Fixed Green and Blue curve adjustment values in R3D metadata
• Fixed max fan speed in adaptive modes

OPERATIONALNOTESSPECIFIC TO BUILD v6.2.60

• ProRes only playback is not supported
• Secure Format media before using Pre-Record.
• Please perform an Auto-Cal after upgrading from v6.1.6.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.

DSMC Release Build v6.2.57 May 17, 2016

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.2.57.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.2.57.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.2.57.
• You cannot downgrade a WEAPON CF to earlier than v6.1.50 or v6.2.57 after upgrading to v6.2.57.
• You cannot downgrade a WEAPON MG, SCARLET-W or REDRAVEN to earlier than v6.2.57 after upgrading to v6.2.57.
• You must upgrade your REDMOTE firmware to v9.5.×. Download the firmware upgrade from red.com/downloads.
• Refer to the REDDSMC Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v6.2.57.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.2.57

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDSTATIONREDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.2.55

• Added flip video support in R3D metadata
• Fixed audio output disabled after setting Headphone Volume to -dB value (DSMC2 only)
• Fixed Base Expander distorted live audio after playback (DSMC2 only)
• Fixed invalid Apple ProRes and Avid DNx clips recording 6K Full Frame at 82.81fps (DSMC2 only)
• Fixed horizontal split in monitor at max frame rates in 6K/5K formats (DSMC2 only)
• Fixed repeated columns in right side of monitor (DSMC2 only)
• Fixed HD-SDI cutout in playback with genlock
• Fixed HD-SDI flip/mirror with genlock
• Fixed HD-SDI test pattern output with genlock
• Fixed UI Flip/Mirror setting not saved across boots
• Fixed incorrect Gamma Space indication on Histogram during playback
• Fixed incorrect clip count returned in MEDACLPC when playlist exists

OPERATIONALNOTESSPECIFIC TO BUILD v6.2.57

• ProRes only playback is not supported
• Secure Format media before using Pre-Record.
• Please perform an Auto-Cal after upgrading from v6.1.6.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.

DSMC Release Build v6.2.55 April 13, 2016

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.2.55.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.2.55.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.2.55.
• You cannot downgrade a WEAPON CF to earlier than v6.1.44 or v6.2.25 after upgrading to v6.2.55.
• You cannot downgrade a WEAPON MG or SCARLET-W to earlier than v6.2.44 after upgrading to v6.2.55.
• You cannot downgrade a REDRAVEN to earlier than v6.2.51 after upgrading to v6.2.55.
• You must upgrade your REDMOTE firmware to v9.5.×. Download the firmware upgrade from red.com/downloads.
• Refer to the REDDSMC Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v6.2.55.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.2.55

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDSTATIONREDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.2.51

• Added SLA message to Switchblade/Sidekick
• Added 30Hz option for RED Touch 7" LCD
• Added warning to Adaptive Preview/Quiet fan mode (DSMC2 only)
• Added Canon EF-S 18-55mm f3.5-5.6 IS II
• Added Tamron 28-300mm f3.5-6.3 Macro for Canon
• Fix UI slider values when changed externally
• Fix remaining time calculation in magnify mode
• Fix media format failure with REDMOTE attached (DSMC only)
• Fix Apple ProRes 4K 444XQ artifacts with 2K FF 1.3x Anamorphic at 120fps (DSMC2 only)
• Fix Amps display in power dialog for ET Battery and V-Lock I/O Expander modules (DSMC2 only)
• Fix color shift in playback with RED Touch 7" LCD (DSMC2 only)
• Fix magnify in 3K formats (DSMC2 only)
• Fix Base Expander distorted live audio after playback (DSMC2 only)
• Fix HD-SDI sync at 50/59.94 FPS genlock input (DSMC2 only)
• Fix Rear Analog Pre-Amp Gain displayed value (DSMC2 only)
• Fix tearing on LCD after format change
• Fix playback timeline when auto-hide menus enabled
• Fix REDMOTE lockout when SLA is displayed (DSMC only)
• Fix timelapse timer when frame count is larger than 1
• Fix tint value for Auto White Balance
• Fix message when REDVOLT battery installed in REDVOLT XL module
• Improved Adaptive fan mode to protect against overheating in cool ambient temperatures (DSMC2 only)
• Changed SCARLET-W camera ID (DSMC2 only)
• Updated in-camera help files

OPERATIONALNOTESSPECIFIC TO BUILD v6.2.55

• ProRes only playback is not supported
• Secure Format media before using Pre-Record.
• Please perform an Auto-Cal after upgrading from v6.1.6.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.